AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Motorcycle red patina paint job12/7/2023 ![]() ![]() Don’t apply too much just put on a single. Go horizontally and cover the entire tank. Now shake the rattle can of epoxy primer and spray it uniformly on the tank. Then clean it thoroughly with a wet cloth and let the surface dry. The importance of primer is that it protects the metal from damage and moisture as well as makes the paint long-lasting.įor applying the primer, mount the tank on your eye level. Now that the tank is ready, you have to apply the epoxy primer to the tank. Step 5: Spray The Primer Coat On The Tank Also, the spray paint sits easily on the tank when the dents are filled and the surface is smooth. ![]() This not only makes the layer smooth but also increases the durability of the tank. Be consistent and patient while sanding away the dent filler. If dried properly, you need to sand the layer to make the dent merge into the body of the tank. Knock the dent to see if it has dried fully or not. Now let the filler embed strongly into the damaged areas. Put a smooth layer of dent filler and scrape off the extra layer of dent filler from the top. Next, you have to work on the dents.įirst, use dent filler to fill the dents and scratches on the motorcycle fuel tank. The chemical clears out the base layer of paint on the motorcycle tank and gives a smooth surface. Take a rest if you are tired.Īfter sanding the motorcycle tank, use a towel to rub the motorcycle tank with a chemical that completely removes the color and extra residues. Keep sanding in circular motions until the old coating doesn’t get off the tank. Try low-grade sandpaper and then move to medium-grade sandpaper if needed. It not only removes the old paint but also smoothens the metal surface. This is why you have to remove the old paint and repair the dents before you spray paint the tank.įor removing the old paint, use sandpaper to sand away the old coating. The new layer of paint should be done on a smooth surface. Step 4: Remove The Paint And Repair The Dents If you want a sticker or graphic design, spray a clear coat after painting the tank. For a matte finish, use 1k paint coating and for a glossy finish, use a 2k paint coating. Though it depends on your choice, getting a matte finish is easier and more convenient than getting a glossy finish. ![]() You can either go for a matte finish or a glossy finish. Depending on your preference, you can either paint the motorcycle tank with the same color it has or select another color. Now is the turn to choose the color you want to apply. ![]() Though this is optional, it is the right time to clean the tank before you paint it. If you see stubborn buildups and rust, use vinegar and baking soda to clean the interior. Seal the fuel pipe with a clamp.Īfter emptying the tank, clean the inside of the tank by pressure washing. Take out the motorcycle’s tank and empty it if there is any fuel left inside. Then unscrew the bolts and screws with a screwdriver and wrench. First, disconnect the pipe connecting the motorcycle and the tank. Step 2: Detach The Tank And Clean Itĭetaching the motorcycle’s tank is the next step. As toxic fumes are released, you should work with caution. Next, wear safety glasses, hand gloves, and a face mask for your safety. Ventilate the area well with a table fan and add a light source for better visibility. Then prepare your garage for the project. Get all these supplies from a hardware store first. Here is a list of materials you need for painting the tank with a rattle can: This will help you to cut off time and do it in a proper way. But before that, load your brain with one thing, ‘PATIENCE’! Step 1: Gather The Materials For Paintingīefore you start the project, gather the materials first. On that note, I will start mentioning the steps of painting a motorcycle tank with a rattle can. Note that the process can be time-consuming and you can’t just miss out on any of the steps. But you need to have patience for the other jobs you would require to do. The paint is prepared in the can and you can just grab one and spray it (of course in a certain way). Spraying with a rattle can is a lot easier than spraying with a spraying gun. ![]()
0 Comments
Read More
Leave a Reply. |